Motorcycle Electric Hot Handlebar Heated Grips Handle with Independent Switch Three-level Thermostat Motorbike Hot HandlebarFeature: 1] One-piece molding to prevent rain and dust from entering the internal corrosion parts, longer life and safer 2] Built-in intelligent temperature control chip, three-speed adjustable temperature, intelligent temperature control is safer 3] 12V voltage, 22MM handlebar inner diameter, suitable for most motorcycles 4] Double throttle cable buckle, wider installation range 5] The design can be sealed and can be opened, which does not affect the installation of the handle outside the handle, and only the lights and other decorative accessories are installed, which is more beautiful and convenient 6] The product has added a standby mode. After switching to the standby state, the electric heating handle will automatically keep the temperature to about 50 degrees, and it will automatically shut down after two hours. There is no need to worry about running out of the motorcycle battery due to forgetting to turn off the switch. specification [Product gross weight]: 330G [Product material]: Nitrile material [Handle length]: Left handle: 143*36MM; Right handle: 127*36mm [Packing size]: 20x13x6cm [Product color]: black [Suitable pipe diameter]: 22mm [Input voltage]: DC12V [Product power]: red light 35W, blue light 25W, green light 17W [Handle temperature]: low temperature 40C, medium temperature 50C, high temperature 60C [Handle type]: Sealable and openable electric handle [Switch type]: Multi-level adjustable temperature control switch [Applicable models]: 12V motorcycle with a handlebar diameter of 22mm [Product accessories]: 3M glue x1, rearview mirror fixing bracket x1 Instructions: [1] Power on: red light, blue light and green light each flash once and then go out [2] Standby: the red light flashes in the state of breathing, and the temperature reaches the highest temperature, and it will automatically turn to the blue light in the mid-range. It will automatically shut down after 2 hours. [3] Working status: indicator light is always on (high-end: red light is always on, mid-range: blue light is always on, low-end, green light is always on) [4] Long press the power button for 3 seconds: enter the standby state or shut down [5] Click the switch key: switch gears [How to use the switch]: Long press for 3 seconds to turn on the red breathing light, it will automatically turn blue after reaching a certain temperature, lightly press it to change to blue light, the temperature is medium temperature, lightly press twice to change to green, the temperature is Lowest, press three times for the red three-level high temperature, long press for 3 seconds to shut down, standby for 2 hours automatically shut down, no longer have to worry about wasted power consumption Installation Notes: 1Remove the original handlebar [2] Wet the inner hole with soapy water on the left hand, and the twisting amplitude should not be too large when installing [3] When installing the balance iron on the left hand handle, adjust the position of the balance iron to be slightly separated from the handle, and do not squeeze the handle when tightening the screw [4] The power cord, the red wire is connected to the positive pole, and the black wire is connected to the negative pole. Please confirm and then connect it. [5] When installing the left-hand handle, the power cord should be left enough for rotation [6] Put the switch L-shaped bracket on the rear-view mirror, fix it to the rear-view mirror base, and tighten it. Precautions: [1] When installing the left handle, do not twist the handle too much. Excessive twisting will cause the heating wire to shift [2] For models with balance iron, please adjust the installation position of the balance iron. Do not squeeze the handle when tightening the screws. The balance iron is slightly separated from the handle. If the installation position of the balance iron cannot be adjusted, please add a spacer between the balance iron and the handle. Excessive squeezing of the handle will cause difficulty in turning the handle switch and abnormal damage such as the heating wire squeezing out of the handle surface. [Product wiring method]: 1. Connect to the motorcycle electric door lock (behind the key), the red wire to the positive output wire of the electric door lock, and the black wire to any negative electrode or grounding on the car [This method is suitable for use, but it is easy to forget that you don't want to use the standby state Drivers with the switch off] 2. Connect to the positive and negative positions of the battery, connect the red to the positive electrode of the battery [+], and connect the black w