Auto Series6D Waterproof Car Sticker Film6D Waterproof Carbon Fiber Black Car Sticker Film Roll 30cm*152cm Car, Computer, Mobile Phone CaseSize: 30cm x 152cm, black. 6D carbon film is suitable for the interior and exterior of automobiles and other smooth surfaces, such as door handles, steering wheels, mobile phones, computers, furniture, etc. Carbon fiber stickers have the characteristics of waterproof, sunscreen, smooth surface, strong stretchability and durability, and are easy to replace. It is the choice of car enthusiasts to decorate their cars.Convenient maintenance: Reduce the time and cost of washing and waxing the car. If you don't like it, you can remove it at any time. It is easy to stick and remove without damaging the paint surface, leaving no glue residue and does not affect the original appearance of the car.Light, thin and strong: the film is thinner, more flexible and ductile (it can be stretched at will after heating, and will not shrink after returning to normal temperature). It can show ideal tortuosity on small arc surfaces and has long-lasting adhesion; Yellowing, long service life.Isolate corrosion: It can resist most oil, grease, fuel, fatty solvents, weak acids, weak alkalis, weak salts, and isolate continuous damage such as acid rain, gravel, bird droppings, grease, etc.: The toughness recovery force is increased by more than 10 times, automatically closing small scratches, and resisting general scratches, impact and wear.Heat insulation and flame retardant: It can adapt to the temperature difference of -40 to +90 , has good heat insulation and inert temperature conduction functions, and is flame retardant and flame retardant. It does not produce any toxic or secondary pollution to the paint surface, human body and nature. Refracts and filters harmful light, blocks the damage of strong light and UV to the automobile paint, and protects the gloss and durability of the original paint.+ productCorrosion resistance, suitable for temperature differences from -40C to +90C, thermal insulation and flame retardant.Full film covering: no splicing needed, no stitching, no trace, with air guide, no need to worry about air bubbles.Multi-purpose: Can be used as interior decoration, rearview mirror, computer, mobile phone; can be attached to bicycles, motorcycles, cars and furniture.Perfect fit, not prone to wrinkles, no bubbles, no cracks, no deformation.Resistant to water, oil, corrosion, gravel, bird droppings, etc.Adapts to complex curves to fit your car perfectly.FeaturesWeight: 162 gColor:blackMaterial: PVCInstructions:Dry bonding methodSuitable for cars, motorcycles or small carsTools to use:Clean cloth, scraper or credit card1. Clean the body bonding position. If possible, you can use a fiber-free cloth soaked in 50% alcohol or isopropyl alcohol or acetone to scrub. You can also use soapy water. The surface cleaned with solvent must wait for the solvent to evaporate before it can be bonded.2. Under normal circumstances, apply it slowly while scraping it with a tool, and remove the backing paper at the same time.3. If the length and width of the car sticker are less than 10cm, you can remove all the stickers and put them back. But be careful not to accidentally stick it or let it fall to the ground and collect dust.4. Use a clean cloth or scraper [such as a phone card or credit card] to rub or scrape the film diagonally several times until there are no more bubbles in the car sticker.Wet bonding methodSuitable for cars or large vehicles (two-person operation recommended)Tools used: watering can, clean cloth, scraper, utility knife, hair dryer.1. Clean the surface to be pasted. Before preparing the sticker, spray glass water evenly on the surface to be pasted (after cleaning the car body, use a spray bottle to spray water on the part of the car body to be pasted) - mainly to reduce the viscosity of the sticker. Easy to adjust position.2. After determining the location to be affixed, lift one side of the car sticker from right to left [or top to bottom] and press it on the surface of the car with a cloth, then flatten it with a cloth while applying it. . Remove the backing paper.3. When encountering door handles or anti-collision strips, cut the material and wrap or load it according to the situation.4. Make timely adjustments. After confirming the general position of the graphics, use a scraper to repeatedly scrape off water and air bubbles. When using a scraper, scrape diagonally from right to left.5. Use a utility knife to cut the door and car seams evenly, and roll them inward.6. Try to let the moisture in the car sticker dry as much as possible. If possible, you can use a hair dryer to heat it up and dry it moderately.Recommendation: Try not to expose your car to the sun within 24 hours and do not wash your car within 48 hours.5cm x 10M2 PCS300cm x 30cm, silver300cm x 30cm, black5 PCS193*126cm, silver480*175*120cm, silver440*180*160cm, black110*50cm, 2pcs10M*8mm